Logo

P1390 Engine Trouble Code

P1390 Engine

When you check engine light came on code P1390 the reason should be Engine Light ON (or Service Engine Soon Warning Light). However your vehicle's manufacturer may have a different definition for the P1390 OBD-II Diagnostic Powertrain (P) Trouble Code. So you should chech it on our car models.

Theoretically you can drive a few more days or even months with a broken MAF sensor in your car. You will notice a decrease in gas mileage/km and over time the car will at the end start stalling a lot from engine side. At a shop, the replacement cost is between $300-$450 depending on the car, but that's usually the cost of parts because the labor is relatively simple.

P1390 Code Meaning :

P
OBD-II Diagnostic Powertrain (P) Trouble Code For Engine
1
Fuel And Air Metering
3
Fuel Rail Pressure Sensor Circuit Malfunction
9
Cylinder 4 Contribution/Balance Fault
0
Exhaust Gas Recirculation Sensor B Circuit High

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

P1390 OBD-II Diagnostic Powertrain (P) Trouble Code Description

P1390 OBD-II Trouble Code Octane Adjust Pin Out Of Self Test Range is one of the definitions for the P1390; however your vehicles manufacturer may have a different definition for the P1390 code. Please check below for your spe P1390 code. Fuel Rail Pressure Sensor Circuit Malfunction and Cylinder 4 Contribution/Balance Fault causes most of code P1390.

Reason For P1390 Code

The reason of P1390 OBD-II Engine Trouble Code is Fuel Rail Pressure Sensor Circuit Malfunction.

P1390 DTC specifically refers to the camshaft (cam) timing. In this case, if the cam timing is over-retarded, the engine trouble light will be illluminated and the code will be set.

How To Repair P1390 Code

Before starting let's see P1390 repairing process steps:

  • Qualified technicians will begin by using a scan tool to access P1390 code stored in the ECU.
  • Technicians will note P1390 code present and any freeze frame data associated with them.
  • After all, if you sure the engine trouble is finished, the code will be cleared.

B for the vehicle's clutch is giving the wrong voltage readings, there could be an issue with the solenoid, the sensor, the wiring, or with the clutch itself. Shifting may become harsh, and other transmission problems may occur.

This can result in damage to engine parts over duration of time. We consider that you seal the engine leaks right away if possible. Rising fuel usage can often be associated to a defect in how your engine generates fuel. When matched up with a check engine light in sight and other engine-associated symptoms, the issue can be even more critical. If you see that your vehicle is consuming more fuel, have it inspected and repaired by a mechanic.

Sometimes P1390 code comes with P139000 code.

Diagnosis Of Engine Error OBD Code P1390

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a P1390 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the P1390 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.

All Engine Trouble Codes

All engine trouble codes with P, U, B and C engine codes.

Code Search

Please fill the "Code Box" to find engine fault code.

Example: 0140

Car Models :

Please select your car.

How To Read Engine Codes ?

Ways to read engine trouble codes.

How To Clear Check Engine Lights ?

Ways to clear check engine light on car panel.

Check Engine Light Dictionary

Ways to clear check engine light on car panel.